Too bad there's no USB equivalent of that now. Snow Leopard, which is what I think I was running the last time I used the drive). Other than it showing up in the System Report, there is no sign that the computer sees the drive.Īnyone have other ideas? I was thinking of scheduling a Genius Bar appointment and asking them to borrow a boot drive for older OSes (e.g. (I haven't tried a Tech Tool Pro since it appears to cost money.) I've rebooted without the disks inserted in the drive, rebooted with disks inserted, rebooted and immediately inserted a disk and held the option key, all without success. They aren't listed in diskutil either, and Disk Genius doesn't see them. Open Computer Management by clicking the Start button, clicking Control Panel, clicking System and Security, clicking Administrative Tools, and then double-clicking Computer Management. Method 2: Check the status of hard drive in disk management, follow these steps: a. The light on the drive blinks fast for a minute or so, then blinks slow until I eject the disk. You may check if the hard drive work on different computer. When I insert any of the 3 disks, the drive spins for a second, then stops. Iomegas site says the following about that qualified for 32-bit Windows 7: 'Zip® Drives: Zip® 100MB, 250MB or 750MB USB, ATAPI, FireWire or SCSI drives should work with native Windows 7 drivers. With both computers, when the drive is attached and I run a system report, the USB Zip 250 drive appears in system report, and the serial # is detected. I've tried hooking the drive up to two different macs, one running High Sierra, the other running El Capitan. I'm using a USB external Zip 250 drive, and trying without success to mount 3 Zip disks, all 100 MB, all Mac formatted. Too bad there's no USB equivalent of that, did you ever figure out how to get your Zip disks to mount? Once loaded, the driver should remain loaded until the Mac is shut down or restarted.īack in the days of the Classic Mac OS, there was a utility called SCSI Probe that would "scan the bus" while running, and load drivers and drives where found. When you boot with the option key held down, this instructs the Mac to "scan all connected drives" to look for bootable copies of the OS.Įven though the ZIP disk doesn't have a copy of the OS on it, the Mac should scan the USB bus, and load the on-disk driver. When you get to the finder, do you see the ZIP disk on the desktop?Įvery Mac-formatted ZIP disk has a copy of the "on-disk driver" on it. Click on it with the mouse pointer and hit return.ĥ. When connecting the IDE/EIDE cable to the back of the Zip. It should connect with the colored side of the cable facing the power connection. Often, the red or blue side of the cable represents pin 1. Hold down the option key on the keyboard (keep holding it until the startup manager appears)Ĥ. Once the Zip disk drive has been installed into the computer, connect the IDE/EIDE interface cable to the back of the zip drive. Push ZIP disk all the way in, and then.ģc. Now - power on, and IMMEDIATELY (or as quickly as possible)ģb. Have a ZIP disk "halfway inserted" into the driveģa. Power down - all the way off (leave ZIP drive connected).Ģ. I deleted them from all of my ZIP disks and never backed them up.1. Thanks to the OP for posting the archive of the tools. You don't *need* to install any of the Iomega tools to access the drive in Windows 95 (guest.exe is not required) as long as your SCSI drivers are working correctly. I had some issues with remnants of the old Windows 3.11 ASPI drivers hanging around after the Windows 95 upgrade that were causing the system to lockup. You can keep both if you use a startup menu to boot directly into DOS or games or whatever and want to access the drive. Windows 95: you will want to disable any 16-bit ASPI drivers in DOS and install the appropriate 32-bit ASPI drivers into Windows 95. To access the ZIP/Jaz/etc drive from DOS or Windows, you have to use guest.exe to assign it a drive letter (which you can put in your autoexec.bat). If you don't have those, you can try various Adaptec drivers, as many cards will work with those. My memory of the intricacies of ASPI had long faded away.ĭOS/Windows 3.x: you will need for ASPI drivers that hopefully came with your SCSI card. In an effort to keep this thread properly necro'ed, I wanted to answer the above as I have just gone through the process of getting an old SCSI ZIP100 working on a W311 machine that I "upgraded" to Windows 95.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |